House Extension Drawings in Marks Gate |

No Article 4 Direction covers Barking and Dagenham, which keeps the Marks Gate permitted-development route open on unlisted houses. The Marks Gate setting is post-war estate, which shapes what passes near Marks Gate. A Marks Gate address in Becontree Estate (historic) or Eastbury loses part of its permitted development, so we usually take the RM6 scheme to Barking and Dagenham Council as a full application from the outset. Every Marks Gate enquiry starts with that check.

How Article 4 directions apply to your Marks Gate street is settled at survey stage, not after submission. Everything on a Marks Gate scheme is measured from the post-war estate outward. The borough policy layer over every RM6 address is set out on Barking and Dagenham planning. The Marks Gate survey then carries into architectural drawings in Marks Gate if the project runs on to construction.

Validation at London Borough of Barking and Dagenham is the first delay a Marks Gate applicant meets. We measure the RM6 property on site with a laser, then draw the existing set from that data alone.

Statutory periods: 8 weeks from validation for a householder application, 13 weeks for a major scheme, 6 weeks for prior approval with a 21 days neighbour consultation, and 5 weeks for a full plans building control submission. A party structure notice requires one month notice and two months where excavation is involved.

Officer queries on a Marks Gate application come to us, not to you. The set is checked against the London Borough of Barking and Dagenham validation list before it goes in.

On Marks Gate terraces the objection to expect is loss of light to a rear window. A Marks Gate survey takes two to three hours and needs access to every room.

On Marks Gate terraces the flank wall is usually shared, so the party wall notice should go out well before work starts. Once consent is granted, planning permission follows for the RM6 property.

Marks Gate is characterised by post-war estate, concentrated across RM6 in the Chadwell Heath area. The post-war estate is the constraint that shapes most Marks Gate projects, long before policy enters the picture. On RM6 plots specifically, post-war houses on these estates often sit under an estate management scheme, which can remove permitted development independently of any Article 4 direction. That is drawn out in the Marks Gate proposed section. Barking and Dagenham Council reads a Marks Gate elevation against its neighbours first.

A RM6 dig turns on engineering more than on policy. Survey once, use it for every RM6 submission that follows.

What the Marks Gate drawing pack contains

Here is what a RM6 instruction actually produces.

• existing and proposed ground-floor plans for the Marks Gate property
• proposed rear elevation
• long section through the extension
• site and block plans
• party wall position drawing

Local landmarks that shape a Marks Gate application

• Marks Gate — a Marks Gate roof extension is judged against the datum it sets.
• Chadwell Heath — massing on adjoining RM6 plots is tested against it.

Getting to a Marks Gate survey

Surveyors travel to RM6 addresses from the studio; the nearest stations are Newbury Park, Chadwell Heath. Appointments are booked in Marks Gate on weekdays and Saturdays, and the measured survey of a standard post-war estate takes two to three hours.

Where Marks Gate sits

on Ordnance Survey grid reference TQ485905. The RM6 block plan is set out from that grid square. Source.

Practical detail for a Marks Gate submission: Marks Gate is served by Newbury Park and Chadwell Heath; ROMFORD is the post town on Marks Gate addresses; dialling code 020. Site plans are drawn to the address as Barking and Dagenham Council holds it.

Marks Gate postcode coverage

Surveys run across RM6 (Chadwell Heath), shared with Chadwell Heath throughout Barking and Dagenham.

Streets and stations in Marks Gate

Most Marks Gate sites are within walking distance of Newbury Park or Chadwell Heath.

Areas we cover around Marks Gate

Marks Gate aside, we also cover Ilford (IG1), Barkingside (IG6), Gants Hill (IG2), Snaresbrook (E11), Stratford (E15), Forest Gate (E7) and the Newham boundary.

The variables on a RM6 job are structural: party walls, floor levels, and whether the Becontree Estate (historic) designation adds a heritage statement.

Statutory application fees are set by regulation, not by the council: £548 householder, £610 for a new dwelling, £274 for a lawful development certificate, £249 for prior approval.

We invoice the drawings only; London Borough of Barking and Dagenham takes the statutory fee from the Marks Gate applicant. London planning approval-rate dataset · Barking and Dagenham planning · the London house extension drawings pillar page · house extension drawings in Ilford.

A chartered technologist surveys the Marks Gate property and signs the drawings — the same person, start to finish. Where Becontree Estate (historic) or a RM6 party wall complicates a Marks Gate scheme, Barking and Dagenham Council sees it early.

Drawings are produced by chartered members of the Chartered Institute of Architectural Technologists (MCIAT), the professional body for technical design and building-regulations competence. First-time approval across our London caseload is 98%. Statutory fees shown are those in force in England in 2026 under the Town and Country Planning (Fees for Applications) Regulations. Confirm your local authority at gov.uk and submission requirements on the Planning Portal. Studio: 71–75 Shelton Street, London WC2H 9JQ.

Send the Marks Gate address; we will come back with the route and the fee. This Marks Gate page was reviewed in August 2026.